安规网 » 电线电缆插头插座认证 » 关于UL线缆测试的讨论贴!
«123 4 5678» Pages: ( 4/10 total )
本页主题: 关于UL线缆测试的讨论贴! 打印 | 加为IE收藏 | 收藏主题 | 上一主题 | 下一主题

wangrang



头衔:過了...淡了 過了...淡了

级别: 安规学徒
精华: 1
发帖: 271
安规威望: 83 点
安规金币: 575 个
安规宣传: 0 次
安规测试报告: 0 份
在线时间:987(小时)
注册时间:2007-05-17
最后登录:2011-09-26

在進行拉伸測試的時候,測啞鈴片厚度時只測4個點就可以了,然後取最小值,這個在UL1581裏面是有規定的...

本文由wangrang在供参考的旧版安规网发表,建议进入新版交流!
顶端 Posted: 2007-08-10 16:56 | 45 楼    新版 | 安规网
dzxtt




级别: 安规新人
精华: 0
发帖: 3
安规威望: 26 点
安规金币: 505 个
安规宣传: 0 次
安规测试报告: 0 份
在线时间:0(小时)
注册时间:2007-07-26
最后登录:2007-11-05

热延伸是否是线材老化后的伸长率呢?标准里有规定的啊

本文由dzxtt在供参考的旧版安规网发表,建议进入新版交流!
顶端 Posted: 2007-08-12 13:24 | 46 楼    新版 | 安规网
jeremyho88


级别: 安规版主
精华: 2
发帖: 1265
安规威望: 154 点
安规金币: 922 个
安规宣传: 0 次
安规测试报告: 0 份
在线时间:2052(小时)
注册时间:2007-07-30
最后登录:2012-01-21

投影仪是很不方便的,用测厚仪(也就是装在支架上的千分尺,或手持测厚仪)就很好。哑铃片用成型要注意各向异性的问题。太薄了成型有问题,最好厚一点,再用磨片机磨平。如果使用压片机,一定注意多压几次,就像做面条时多多糅合,否则由于未充分塑化,强度和伸长率都偏小

本文由jeremyho88在供参考的旧版安规网发表,建议进入新版交流!
本帖最近评分记录:
  • 安规金币:+10(新王龙李云峰) 积极讨论
  • 认真做事,老实做人,互相学习,共同提高
    顶端 Posted: 2007-08-12 18:59 | 47 楼    新版 | 安规网
    cableyzf




    级别: 安规工程师
    精华: 1
    发帖: 1017
    安规威望: 160 点
    安规金币: 775 个
    安规宣传: 0 次
    安规测试报告: 0 份
    在线时间:727(小时)
    注册时间:2007-06-07
    最后登录:2011-10-20

    投影仪测试还是比较准确的,但是同样的它是建立在压片质量较好的基础上才行。现在很多压片机压出的片厚度不均匀,而且或多或少有一些气孔。根据经验在操作时增加一个耐热薄膜会提高压片的质量

    本文由cableyzf在供参考的旧版安规网发表,建议进入新版交流!
    本帖最近评分记录:
  • 安规金币:+10(新王龙李云峰) 积极讨论
  • 顶端 Posted: 2007-08-14 15:28 | 48 楼    新版 | 安规网
    李云峰
    资助会员

    级别: 安规总版主
    精华: 0
    发帖: 2243
    安规威望: 1045 点
    安规金币: 15335 个
    安规宣传: 3 次
    安规测试报告: 0 份
    在线时间:4662(小时)
    注册时间:2007-05-10
    最后登录:2012-01-27

    投影仪是用于破坏性的测量,对于结构测量和小样测量是比较合适的!但是相对于哑铃片来说就不太合适了,因为破坏了的哑铃片是没有办法做测试的了!本人看法!

    本文由李云峰在供参考的旧版安规网发表,建议进入新版交流!
    采菊东篱下,悠然见南山.
    顶端 Posted: 2007-08-20 17:29 | 49 楼    新版 | 安规网
    李云峰
    资助会员

    级别: 安规总版主
    精华: 0
    发帖: 2243
    安规威望: 1045 点
    安规金币: 15335 个
    安规宣传: 3 次
    安规测试报告: 0 份
    在线时间:4662(小时)
    注册时间:2007-05-10
    最后登录:2012-01-27

    Quote:
    引用第47楼dzxtt于2007-08-12 13:24发表的  :
    热延伸是否是线材老化后的伸长率呢?标准里有规定的啊

    热延伸是针对材料的测试,不是老化后的伸长率,他是要求在一定的温度下对试样施加一定的机械负荷,等到规定的时间以后测量负荷下的伸长和撤去负荷的伸长,与原试样的长度之比!


    [ 此贴被新王龙李云峰在2007-08-20 18:16重新编辑 ]

    本文由李云峰在供参考的旧版安规网发表,建议进入新版交流!
    采菊东篱下,悠然见南山.
    顶端 Posted: 2007-08-20 17:50 | 50 楼    新版 | 安规网
    xiaoxiangtongzi

    头衔:新手上路 新手上路

    级别: 安规版主
    精华: 0
    发帖: 3711
    安规威望: 406 点
    安规金币: 7969 个
    安规宣传: 0 次
    安规测试报告: 0 份
    在线时间:2384(小时)
    注册时间:2007-07-05
    最后登录:2012-02-06

    有的也叫加热变形试验-----实际与楼上李兄说的是一样的;
    例如--UL62规定:
    NMX-J-191
    Heat Deformation of Semiconductive Shielding, Insulations and Protective Coverings of Electrical
    Conductors – Test Method

    5.1.3 Deformation
    5.1.3.1 Insulation
    The insulation on single-conductor wires, and on the individual conductors (separated, in the case of
    parallel cords), shall not decrease by more than 50% in thickness when subjected to a force caused by a
    mass as shown in Table 40, and while maintained at the temperature shown in Table 40 for 1 h.
    5.1.3.2 Jacket
    Smoothed specimens of jackets from finished cords and cables shall not decrease by more than 50% in
    thickness when subjected to a force caused by a mass of 2000 g, and while maintained at the temperature
    shown in Table 40 for 1 h.
    5.1.3.3 Method
    Compliance with Clauses 5.1.3.1 and 5.1.3.2 shall be determined in accordance with the method
    described in CSA C22.2 No. 0.3, Clause 4.3.6.1; UL 1581, Section 560; or NMX-J-191-ANCE.

    本文由xiaoxiangtongzi在供参考的旧版安规网发表,建议进入新版交流!
    本帖最近评分记录:
  • 安规金币:+10(新王龙李云峰) 经验分享
  • http://www.angui.org/BBS/?a=xiaoxiangtongzi
    顶端 Posted: 2007-08-20 19:27 | 51 楼    新版 | 安规网
    wangrang



    头衔:過了...淡了 過了...淡了

    级别: 安规学徒
    精华: 1
    发帖: 271
    安规威望: 83 点
    安规金币: 575 个
    安规宣传: 0 次
    安规测试报告: 0 份
    在线时间:987(小时)
    注册时间:2007-05-17
    最后登录:2011-09-26

    有沒有誰比較了解HPN線材的耐電弧測試的呢?說說吧!

    本文由wangrang在供参考的旧版安规网发表,建议进入新版交流!
    顶端 Posted: 2007-08-29 13:28 | 52 楼    新版 | 安规网
    xiaoxiangtongzi

    头衔:新手上路 新手上路

    级别: 安规版主
    精华: 0
    发帖: 3711
    安规威望: 406 点
    安规金币: 7969 个
    安规宣传: 0 次
    安规测试报告: 0 份
    在线时间:2384(小时)
    注册时间:2007-07-05
    最后登录:2012-02-06

    Quote:
    引用第53楼wangrang于2007-08-29 13:28发表的  :
    有沒有誰比較了解HPN線材的耐電弧測試的呢?說說吧!

    参照UL62 第 5.2.5~5.2.6条.UL62-2006版第49页.~呵呵~
    5.2.5 Standard arcing test for Type HPN
    5.2.5.1 General
    Type HPN cord shall not arc when a specimen of finished cord is connected at one end to a 120 V (rms)
    source of supply through a 15 A fuse or circuit breaker and subjected to a standard test flame applied 13
    mm (0.5 in) from the other end of the specimen for 2 min. Compliance shall be determined in accordance
    with the method described in Clause 5.2.5.2; CSA C22.2 No. 0.3, Clause 4.28.12; or UL 1581, Section 1670.
    5.2.5.2 Test method
    The specimen for test shall be of any suitable length. One end shall be cut off square, care being taken
    that the conductor ends are flush with the cut end of the cord. The cord shall be laid across a
    nonconductive surface, the square cut end protruding approximately 0.1 m (4.0 in) beyond the surface
    edge. The opposite end shall be connected to the voltage source between the conductors of a
    two-conductor cord and between the circuit conductors joined together and the grounding conductor of a
    three-conductor cord. Using a Tirrill, Bunsen, or similar appropriate gas burner, a standard test flame (as
    described in Clause 5.1.5.1) shall be obtained. With its barrel vertical, the burner shall be placed under
    the free end of the cord with the tip of the inner blue cone touching the flat underside of the specimen
    midway between the conductors and 13 mm (0.5 in) from the square end for a 2 min period. The cord
    does not comply if arcing occurs between the conductors during application of the flame or if the fuse or circuit breaker opens.
    =======================
    5.2.6 Flex arcing test for Type HPN
    ===========================
    5.2.6.2 Procedure
    The procedure shall be as follows:~

    本文由xiaoxiangtongzi在供参考的旧版安规网发表,建议进入新版交流!
    本帖最近评分记录:
  • 安规金币:+5(新王龙李云峰) 信息分享
  • http://www.angui.org/BBS/?a=xiaoxiangtongzi
    顶端 Posted: 2007-09-10 16:53 | 53 楼    新版 | 安规网
    wangrang



    头衔:過了...淡了 過了...淡了

    级别: 安规学徒
    精华: 1
    发帖: 271
    安规威望: 83 点
    安规金币: 575 个
    安规宣传: 0 次
    安规测试报告: 0 份
    在线时间:987(小时)
    注册时间:2007-05-17
    最后登录:2011-09-26

    標準有看過,其實只是沒有看過具體的測試,有點抽象...

    呵呵,謝謝拉!

    本文由wangrang在供参考的旧版安规网发表,建议进入新版交流!
    顶端 Posted: 2007-09-11 08:47 | 54 楼    新版 | 安规网
    jack123456




    级别: 安规学徒
    精华: 0
    发帖: 136
    安规威望: 32 点
    安规金币: 323 个
    安规宣传: 0 次
    安规测试报告: 0 份
    在线时间:22(小时)
    注册时间:2007-09-03
    最后登录:2008-04-03

    我搞PVC电缆料,不知有什么可以帮上忙

    本文由jack123456在供参考的旧版安规网发表,建议进入新版交流!
    顶端 Posted: 2007-09-11 11:20 | 55 楼    新版 | 安规网
    李云峰
    资助会员

    级别: 安规总版主
    精华: 0
    发帖: 2243
    安规威望: 1045 点
    安规金币: 15335 个
    安规宣传: 3 次
    安规测试报告: 0 份
    在线时间:4662(小时)
    注册时间:2007-05-10
    最后登录:2012-01-27

    只要与UL电源线有关的测试疑问和经验,大家都可以在这里交流的!但是最重要的还是讨论实际测试方法和手段与标准的理解 !

    本文由李云峰在供参考的旧版安规网发表,建议进入新版交流!
    采菊东篱下,悠然见南山.
    顶端 Posted: 2007-09-11 19:25 | 56 楼    新版 | 安规网
    yezi2008ltk




    级别: 安规新人
    精华: 0
    发帖: 2
    安规威望: 7 点
    安规金币: 246 个
    安规宣传: 0 次
    安规测试报告: 0 份
    在线时间:1(小时)
    注册时间:2008-07-18
    最后登录:2008-09-20

    Quote:
    引用第43楼cableyzf于2007-08-10 14:31发表的  :
    对,是最小截面积(最小厚度乘以宽度),平时都没注意。虽然UL1581没说,我查了一下JIS有规定最小厚度(JIS要求至少要测五个值)乘以宽幅得出截面积。检测标准这部分真的是越抠越细,所以这部分的讨论太重要了。谢谢版主!


    UL1581中有规定的:在标志线处,标志线内6MM及19MM处共测试4点取最小值--440.24 The thickness of the specimen is to be taken as the smallest of four measurements to 0.001 inchor 0.01 mm, two of which are to be made at 1/2-inch or 13-mm intervals between the bench marks on oneedge beginning 1/4 inch or 6 mm from either mark, with the other two measurements being made at corresponding points on the opposite edge.

    本文由yezi2008ltk在供参考的旧版安规网发表,建议进入新版交流!
    顶端 Posted: 2008-07-19 00:01 | 57 楼    新版 | 安规网
    maq88


    级别: 安规新人
    精华: 0
    发帖: 1
    安规威望: 7 点
    安规金币: 234 个
    安规宣传: 0 次
    安规测试报告: 0 份
    在线时间:1(小时)
    注册时间:2008-09-08
    最后登录:2008-09-10

        对于UL 可能是我最熟悉不过的,我们公司实验室申请的UL758,UL62,UL1581的目击测试已于2008年9月15日完成.是全球唯一一家可以做目击测试的公司.刚来公司,希望和大家交流交流.

    本文由maq88在供参考的旧版安规网发表,建议进入新版交流!
    顶端 Posted: 2008-09-08 20:40 | 58 楼    新版 | 安规网
    雨花石

    头衔:天天学习,天天向上 天天学习,天天向上

    级别: 安规工程师
    精华: 0
    发帖: 1614
    安规威望: 152 点
    安规金币: 827 个
    安规宣传: 0 次
    安规测试报告: 0 份
    在线时间:980(小时)
    注册时间:2008-07-01
    最后登录:2011-12-06

    学习学习,我才作过两个电线的案子。

    本文由雨花石在供参考的旧版安规网发表,建议进入新版交流!
    不小心踩到了郁金香,它却将香味留在你的脚上,这就叫宽容。
    顶端 Posted: 2008-09-11 15:58 | 59 楼    新版 | 安规网
    «123 4 5678» Pages: ( 4/10 total )
    安规网 » 电线电缆插头插座认证


    安规网免责声明
    安规网已运行
    安规网所有的原创文章,版权归安规网和作者共同拥有,未经许可,任何网站不得非法盗链、转载及抄袭!
    网友文章或评论仅代表作者个人观点并由其承担相应法律责任,不代表本站观点!如果侵犯了您的权益,请提供相关证明,我们将尽快删除!
    安规网为非经营性技术论坛,所有资源均为网友自主提供,仅供个人学习与研究,版权归原作者,切勿用于商业用途,否则一切后果与安规网无关!

    关于我们 | 认证工具 | 免责声明 | 法律条款 | 广告服务
    Total 0.039365(s) query 7, Time now is:03-29 15:57, Gzip enabled
    Powered by Angui.org Support by PHPWind

    安规网版权所有 安规网 安规网论坛 安规认证论坛 Copyright Reserved
    粤ICP备07035324号